420-ALL-DAY

ok i have a 400w hps setup, w/ a 400w mh conversion bulb in it right now, & i turned it off to do some work, & now when i try to turn it back on the ballast hums louder than normal & the 400w mh bulb flickers lightly. all this equipment is brand new & has only been used for about 2wks on a 24/0 cycle. any ideas. thanks

__________________
MaRiJuAnA - at least its not crack
I dont need a scale for the work I can eyeball purp, I am not you jerk hatin on me will make your situation worse you dont wanna take a ride in that long black hearse all eyes on me, shawty im a bomb first im the truth and they say the truth hurts.

ZoomBoom

How long ago did you turn it off? Do you have a digital or magnetic ballast?

You may need to wait longer if its magnetic, they require more time in between on periods to ignite.

__________________
My current grow journal
Gardenscure Nursery Questionnaire
The Complete Guide To Sick Plants, pH and Pest Troubles
my pen writes like this
Posting Guidelines
Accepted Use Policy
St0ney's Soil & Hydroponic pH Nutrient chart

GreenDragon2k

let it cool down and screw the bulb in tighter, & try it again...

__________________
"Herb is the healing of a nation, alcohol is the destruction. " ~ Bob Marley

420-ALL-DAY

it was off for about 15-20mins, & its a HTG Supply 400 Watt Magnetic Ballast.

__________________
MaRiJuAnA - at least its not crack
I dont need a scale for the work I can eyeball purp, I am not you jerk hatin on me will make your situation worse you dont wanna take a ride in that long black hearse all eyes on me, shawty im a bomb first im the truth and they say the truth hurts.

420-ALL-DAY

i tryed screwing in the bulb tighter, ill just try to let it cool longer, & try later. if this doesnt work any ideas what else it could be.

__________________
MaRiJuAnA - at least its not crack
I dont need a scale for the work I can eyeball purp, I am not you jerk hatin on me will make your situation worse you dont wanna take a ride in that long black hearse all eyes on me, shawty im a bomb first im the truth and they say the truth hurts.

Quantrill

bunk bulb

__________________
Each man must for himself alone decide what is right and what is wrong, which course is patriotic and which isn't.

~Mark Twain

bn8up

failing cap or start assist? just throwin it out there if u have an ohm meter run it cross the cap it shoul raise up to the mfd or ufd deppending on what type of cap if it drops rapidly its out if slowlhy runs down its good start assist i have no clue

Farmah

did u wipe the bulb down with a cloth before screwing it in while holding the bulb with a cloth of some sort while screwing? the reason for this is the oil in our fingers...it messes up the bulb. try wiping the bulb maybe it can prevent further damage.

n_d_shadows

Not that this is your issue, but I've seen it on some sockets, the little metal tab in the bottom needs to be pulled up just a bit so it connects better with the bulb.
Dont do that with things plugged up tho, ok?

bagboy

i had an issue with a 400w magnetic.... call em up and tell em, they'll send ya a new one... the replacement has been workin fine since i got it(2mos).... i think they get used magnetic ballasts, and some of em work for a little while, then die.

i had ordered two bulbs, and the first hps did this, so i put in the 2nd, and it did it to the 2nd one as well... so i tossed in the MH conversion, and it worked fine for a month, then took a crap.

more likely than not, the ballast and bulb is dead. htgsupply will replace it no prob, make sure you get a replacement bulb.

__________________
gc chat
complete grows:
second hempy grow
first hempy grow